[jboss-jira] [JBoss JIRA] (WFLY-6762) Windows ennvironment: Wildfly failover test not working when Network Disabling on a VM(Node) or by Shutting down the VM (Node).

[ https://issues.jboss.org/browse/WFLY-6762?page=com.atlassian.jira.plugin.... ] Preeta Kuruvilla updated WFLY-6762: ----------------------------------- Description: In your mail related to WFLY-6749 you has said the below :- **The default stack contains the following failure detection protocols: FD_SOCK FD_ALL These protocols are described here: http://www.jgroups.org/manual/index.html#FailureDetection I suspect that your method of simulating a failure - by disabling the network of the host machine is not being detected by FD_SOCK. It will however, be detected by FD_ALL, but only after 1 minute. The heartbeat timeout used by FD_ALL can be manipulated via the timeout property. e.g. <protocol type="FD_ALL" ><property name="timeout">60000</property></protocol> ************************************************************************************************** Thanks for the quick response on WFLY-6749. Based on your suggestion, I had a taken a look at the testing scenarios mentioned in "Table 29. Failure detection behavior" in the link that you provided- http://www.jgroups.org/manual/index.html#FailureDetection. No where its mentioned that disabling a network on a node, is a valid testing scenario in Wildfly cluster. The Failover is working properly when the network on a node is disabled on a weblogic cluster for our application. However it doesn't work and it hampers the application functionality on Wildfly cluster when we try to disable the network on a node in Wildfly cluster. However as I said earlier, the failover on wildfly cluster works when we stop a node from admin console or give Ctrl + C to stop the services on a node. Would like to get a confirmation from you that disabling the network on a node is not the valid failover testing scenario for wildfly cluster. Also we tried to test the same failover scenario by Shutting down a VM (node) in a wildfly cluster. It did not work for Windows Environment although it worked for linux environment. Note: we are using Windows 2012 environment. Here is a link I found: http://stackoverflow.com/questions/31218710/unable-to-stop-wildfly-8-2-se... Thanks, Preeta was: In your mail related to WFLY-6749 you has said the below :- **The default stack contains the following failure detection protocols: FD_SOCK FD_ALL These protocols are described here: http://www.jgroups.org/manual/index.html#FailureDetection I suspect that your method of simulating a failure - by disabling the network of the host machine is not being detected by FD_SOCK. It will however, be detected by FD_ALL, but only after 1 minute. The heartbeat timeout used by FD_ALL can be manipulated via the timeout property. e.g. <protocol type="FD_ALL" ><property name="timeout">60000</property></protocol> ** Thanks for the quick response on WFLY-6749. Based on your suggestion, I had a taken a look at the testing scenarios mentioned in "Table 29. Failure detection behavior" in the link that you provided- http://www.jgroups.org/manual/index.html#FailureDetection. No where its mentioned that disabling a network on a node, is a valid testing scenario in Wildfly cluster. The Failover is working properly when the network on a node is disabled on a weblogic cluster for our application. However it doesn't work and it hampers the application functionality on Wildfly cluster when we try to disable the network on a node in Wildfly cluster. However as I said earlier, the failover on wildfly cluster works when we stop a node from admin console or give Ctrl + C to stop the services on a node. Would like to get a confirmation from you that disabling the network on a node is not the valid failover testing scenario for wildfly cluster. Thanks, Preeta -- This message was sent by Atlassian JIRA (v6.4.11#64026)