Thanks for your quick response but actually I’ve set that folder as src folder to ensure the they are in classpath at runtime. Paul From: rules-users-bounces(a)lists.jboss.org [mailto:rules-users-bounces@lists.jboss.org] On Behalf Of Alan.Gairey(a)tessella.com Sent: Monday, July 27, 2009 4:19 PM To: Rules Users List Subject: Re: [rules-users] question on adding manual workitem within floweditor You need to make sure that the folder that contains your .conf files is marked as a Source Folder within Eclipse - hopefully it should then work OK. Alan Tessella plc 26 The Quadrant, Abingdon Science Park, Abingdon, Oxfordshire, OX14 3YS E: Alan.Gairey(a)tessella.com, T: +44 (0)1235 555511, F: +44 (0)1235 553301 www.tessella.com Registered in England No. 1466429 This message is commercial in confidence and may be privileged. It is intended for the addressee(s) only. Access to this message by anyone else is unauthorized and strictly prohibited. If you have received this message in error, please inform the sender immediately. Please note that messages sent or received by the Tessella e-mail system may be monitored and stored in an information retrieval system. "Pang, Yonghua" <YPang(a)statestreet.com&gt; Sent by: rules-users-bounces(a)lists.jboss.org 27/07/2009 08:15 Please respond to Rules Users List <rules-users(a)lists.jboss.org&gt; To <rules-users(a)lists.jboss.org&gt; cc Subject [rules-users] question on adding manual workitem within flow editor Hi, I’m a newbie of Drools and I just met a problem when learning Drools Flow according to Drools online documents. I create a workitem, Notification, exactly according to Chapter 8 in Drools Flow Doc. I create MyWorkDefinitions.conf and drools.rulebase.conf, and then put them in classpath. Also, I create one image to be used by the item. However, this new workitem is not found in RuleFlow Editor. I’m not sure if something else is needed. Can you guys please guide me to adding new workitem and dragging/drawing it in RuleFlow Editor? FYI. Though the RuleFlow editor cannot work with the new workitem, the XML style works. I mean, I could manually change the XML of .rf file to use the new workitem. The work environment is JDK5, Drools5, Eclipse 3.4.5 and GEF 3.5. The two conf files are also attached. <<drools.rulebase.conf>> <<MyWorkDefinitions.conf>> Thanks, Paul_______________________________________________ rules-users mailing list rules-users(a)lists.jboss.org https://lists.jboss.org/mailman/listinfo/rules-users

Hi Alan, Thanks so much. It works! By mistake I put my .conf files directly in src folder rather than in META-INF. I the correct folder structure is a must. Regards, Paul From: rules-users-bounces(a)lists.jboss.org [mailto:rules-users-bounces@lists.jboss.org] On Behalf Of Alan.Gairey(a)tessella.com Sent: Monday, July 27, 2009 4:49 PM To: Rules Users List Subject: Re: [rules-users] question on adding manual workitemwithin floweditor Paul, I don't know if the directory structure is significant, but I've attached a screenshot of how the files are configured within my project - with this structure, the work items appear in the RuleFlow editor. (I'm using Eclipse 3.5, but I'm pretty sure this should still work with earlier versions.) Hope this helps, Alan Tessella plc 26 The Quadrant, Abingdon Science Park, Abingdon, Oxfordshire, OX14 3YS E: Alan.Gairey(a)tessella.com, T: +44 (0)1235 555511, F: +44 (0)1235 553301 www.tessella.com Registered in England No. 1466429 This message is commercial in confidence and may be privileged. It is intended for the addressee(s) only. Access to this message by anyone else is unauthorized and strictly prohibited. If you have received this message in error, please inform the sender immediately. Please note that messages sent or received by the Tessella e-mail system may be monitored and stored in an information retrieval system. "Pang, Yonghua" <YPang(a)statestreet.com&gt; Sent by: rules-users-bounces(a)lists.jboss.org 27/07/2009 09:41 Please respond to Rules Users List <rules-users(a)lists.jboss.org&gt; To "Rules Users List" <rules-users(a)lists.jboss.org&gt; cc Subject Re: [rules-users] question on adding manual workitem within floweditor Thanks for your quick response but actually I’ve set that folder as src folder to ensure the they are in classpath at runtime. Paul From: rules-users-bounces(a)lists.jboss.org [mailto:rules-users-bounces@lists.jboss.org] On Behalf Of Alan.Gairey(a)tessella.com Sent: Monday, July 27, 2009 4:19 PM To: Rules Users List Subject: Re: [rules-users] question on adding manual workitem within floweditor You need to make sure that the folder that contains your .conf files is marked as a Source Folder within Eclipse - hopefully it should then work OK. Alan Tessella plc 26 The Quadrant, Abingdon Science Park, Abingdon, Oxfordshire, OX14 3YS E: Alan.Gairey(a)tessella.com, T: +44 (0)1235 555511, F: +44 (0)1235 553301 www.tessella.com Registered in England No. 1466429 This message is commercial in confidence and may be privileged. It is intended for the addressee(s) only. Access to this message by anyone else is unauthorized and strictly prohibited. If you have received this message in error, please inform the sender immediately. Please note that messages sent or received by the Tessella e-mail system may be monitored and stored in an information retrieval system. "Pang, Yonghua" <YPang(a)statestreet.com&gt; Sent by: rules-users-bounces(a)lists.jboss.org 27/07/2009 08:15 Please respond to Rules Users List <rules-users(a)lists.jboss.org&gt; To <rules-users(a)lists.jboss.org&gt; cc Subject [rules-users] question on adding manual workitem within flow editor Hi, I’m a newbie of Drools and I just met a problem when learning Drools Flow according to Drools online documents. I create a workitem, Notification, exactly according to Chapter 8 in Drools Flow Doc. I create MyWorkDefinitions.conf and drools.rulebase.conf, and then put them in classpath. Also, I create one image to be used by the item. However, this new workitem is not found in RuleFlow Editor. I’m not sure if something else is needed. Can you guys please guide me to adding new workitem and dragging/drawing it in RuleFlow Editor? FYI. Though the RuleFlow editor cannot work with the new workitem, the XML style works. I mean, I could manually change the XML of .rf file to use the new workitem. The work environment is JDK5, Drools5, Eclipse 3.4.5 and GEF 3.5. The two conf files are also attached. <<drools.rulebase.conf>> <<MyWorkDefinitions.conf>> Thanks, Paul_______________________________________________ rules-users mailing list rules-users(a)lists.jboss.org https://lists.jboss.org/mailman/listinfo/rules-users _______________________________________________ rules-users mailing list rules-users(a)lists.jboss.org https://lists.jboss.org/mailman/listinfo/rules-users